SMARTbox CAN

Smartbox, based on the Telit Chipset xE910 is a ready to use solution for connecting to CAN Networks to the Cumulocity IoT Cloud. It provides a CAN Slave Communication as well as 2 Sensorinputs and a Modbus RTU Master Communication. Using the MQTT protocol the terminal comes up with a low traffic solution.

Radio

4G LTE LTE Cat 4 (incl. 3G/2G)

LTE Cat 1 (incl. 3G/2G)

LTE Cat M1

NB-IoT (Cat NB1)

3G UMTS | HSPA+ (incl. 2G)

UMTS | HSPA (incl. 2G)

2G GSM | GPRS
Regions EMEA / APAC / Latinamerica / NorthAmerica / Australia / Global (3G / 2G)
GPS Supported by 2G and 3G Variances
Production The selected Region,Technology and GPS can be defined during Production. The default assembly is 3G with supported regions EMEA / APAC

Connectivity

Layout
CAN (Raw)

Type CAN (Raw) | physical CAN
Standard CAN 2.0A | CAN 2.0B

(CAN FD not supported)

Independent CAN-Ports 2 (only 1 supported by firmware)
Isolation galvanic isolation up to 2500V RMS, each port insulated separately
Termination yes, each port independent by DIP switch
Baudrates 50kbit | 100kbit | 125kbit | 250kbit | 500kbit | 1Mbit
Extended CAN format supported
CAN Objects max. 100 different object-identifier possible
Length of data 0…8 Bytes
Send options send on change (on change of cloud data)

send every time interval (0…65535ms)

Receive filters automatic configuration of hardware filters
LED Link CAN-Status

Off: CAN not active

Flickering: CAN RX/TX

On: CAN not active (CAN objects not defined)

LED Act Device-Status

Off: Device is off

Blinking: Firmware is running (waiting for cloud data)

Flickering: Firmware is running (process data transfer)

Fieldbus Modbus

Type Modbus RTU Master
Baudrate 4800, 9600, 19200, 38400, 57600, 115200
Parity Even, ODD, NONE
Stoppbits 2,1
Functioncodes Funct.1 (Read Single Coils)

Funct.3 (Read Holding Registers)

Funct.4 (Read Input Registers)

Funct.5 (Write Coil)y

Datapoints Max. 10 Modbus Slaves, with 100 datapoints per device or 1000 datapoints with 1 device
Sensors 2 Sensor Inputs
DIN/O DIN [voltage free]
AIN NTC | 0..20mA (selectable by Hardware)
LEDs GSM Flashing- connected to mobile network
RUN 2xflashing/pause: StartUp Phase

3xflashing/pause: Connected to Server, Data exchange

Act Flashing: Sensor Board Power
Link Flashing: Sensor Board is ready to process data
USB For programming, Logging and Trace the device

Cloud Connector

Availability All Cumulocity Based systems, Cloud der Dinge Deutsche Telekom
Realtime Clock Updating Realtime automatical from #NTP timeserver
Application CloudFieldbus (CFB Integrated in Devicemanagement)

For SetUp connected field devices

Online Operations Remote Restart

Fieldbus Configuration Cloud-Device

Change Transmitinterval from device to Cloud

Change Communication. Baudrate, Databits, Parity, Stopbits

Operate the connected Field device: Registervalues (R/W)

Operate the connected Field device: Change CoilValues (R/W)

Operate the device with AT Commands in the shell

Communication MQTT
Security TLS-Security 1.0 / TLS 1.2 (ab Version 2.4.x)
Notifications Realtime and Pending Operations
Shell Operate the device with AT Commands in the shell
Location Identification by cellular network or GPS Signal (selected- see Radio)
Tracking Location Route by by cellular network or GPS Signal
Info Operator, Cell ID, LAC, MNC, MCC, Signal strength
Device Database Device database Support for Modbus and Profibus: Measurements, Event, Alarms, Values, Read, Read/Write, Signed/Unsigned, Decimal Places, Multiplier, Divisor, No of Bits, StartBit
OTA RemoteUpdate Software
Data-Exchange Values On Change
Alarms On Change
Events On Change
Measurements Default 900
Signal strength Is sent every 20 Min as a measurement
Offline Buffering Alarms, Events, Measurments ≈ 72h
SMS For Troubleshooting you can operate the device by SMS:

Reboot

Change tenant

FOTA/OTA

General

Dimensions 100 x 70 x 45 mm
Weight 89g
GSM Antenna SMA Connector
Power Supply Nominal voltage range: 12-24 VDC, 10%

Maximum continuous (average) supply power: 2.5 W

Maximum continuous (average) supply current: 200 mA at 12V, 100 mA at 24V

Mounting Via DIN Rail Adapter or Adapter for Wall Mounting
SIM Card Format 2FF
Operating temperature -20..60°C
Storage temperature -40..85°C
Operating humidity Max. 85%
Storage humidity Max. 85%
IP Class IP20/IP54 (opt.)
Approvals     
Conformity Declerations 2014/53/EU (Radio Equipment Directive – RED)

Radio

EN301511 v12.5.1 for GSM 900 and 1800 MHz

EN301908 v11.1.1 for UMTS band 1 and 8

EMC

EN 301489-1 v2.1.1 general part

EN 301489-52 v0.0.7 for GSM and UMTS

Safety

EN60950-01