SMARTbox BLE

Smartbox, based on the Telit Chipset xE910 is a ready to use solution for connecting BLE Devices to the Cumulocity/Cloud of Things IoT Cloud. The SMARTbox acts as a client collecting data from up to 8 BLE devices. Easy connect and configure the used BLE devices in the cloud by Cloud fieldbus. Using the MQTT protocol the terminal comes up with a low traffic solution.

BLE-sensors-Kopie

 Radio

4G LTE LTE Cat 4 (incl. 3G/2G)

LTE Cat 1 (incl. 3G/2G)

LTE Cat M1

NB-IoT (Cat NB1)

3G UMTS | HSPA+ (incl. 2G)

UMTS | HSPA (incl. 2G)

2G GSM | GPRS
Regions EMEA / APAC / Latinamerica / NorthAmerica / Australia / Global (3G / 2G)
GPS Supported by 2G and 3G Variances
Production The selected Region, Technology and GPS can be defined during Production. The default assembly is 3G with supported regions EMEA / APAC

Connectivity

Layout
BLE Qualification v5.0 (Bluetooth low energy)
Type GATT Client
Connectivity -8 Nordic Thingy52 BLE sensors

(Automatic Custom service identification of generic BLE sensors – not released yet)

Chip NINA-B111-02B (ublox)
Fieldbus Modbus

Type Modbus RTU Master
Baudrate 4800, 9600, 19200, 38400, 57600, 115200
Parity Even, ODD, NONE
Stoppbits 2,1
Functioncodes Funct.1 (Read Single Coils)

Funct.2 (Read Input Status)

Funct.3 (Read Holding Registers)

Funct.4 (Read Input Registers)

Funct.5 (Write Coil)

Funct.6 (Write Holding Register)

Datapoints Max. 10 Modbus Slaves, with 100 datapoints per device or 1000 datapoints with 1 device
Sensors Number 12
U1/U2/U3/U4/U5/U6/U7 DIN NO [High Side]

24VDC

U8 0..20mA
U9/U10 DO – Digital Output 24VDC
Output 24VDC Digital Output. Note: Either the Output or the 2nd Fieldbusinterface can be selected during production
DIN/O DIN [voltage free] (defined by Hardwarejumper)
AIN/O NTC (selectable by Hardwarejumper, either NTC or 0..20mA)
AIN/P+ 0…20mA (selectable by Hardwarejumper, either NTC or 0..20mA)
LEDs GSM Flashing- connected to mobile network
RUN 2xflashing/pause: StartUp Phase

3xflashing/pause: Connected to Server, Data exchange

Act Flashing: Sensor Board Power
Link Flashing: Sensor Board is ready to process data
USB For programming, Logging and Trace the device

Cloud Connector

Availability All Cumulocity Based systems, Cloud der Dinge Deutsche Telekom
Realtime Clock Updating Realtime automatical from #NTP timeserver
Application CloudFieldbus (CFB Integrated in Devicemanagement)

For SetUp connected field devices

Online Operations Remote Restart

Fieldbus Configuration Cloud-Device

Change Transmitinterval from device to Cloud

Change Communication. Baudrate, Databits, Parity, Stopbits

Operate the connected Field device: Registervalues (R/W)

Operate the connected Field device: Change CoilValues (R/W)

Operate the device with AT Commands in the shell

Communication MQTT
Security TLS
Notifications Realtime and Pending Operations
Shell Operate the device with AT Commands in the shell
Location Identification by cellular network or GPS Signal (selected- see Radio)
Tracking Location Route by by cellular network or GPS Signal
Info Operator, Cell ID, LAC, MNC, MCC, Signal strength
Device Database Device database Support for Modbus and Profibus: Measurements, Event, Alarms, Values, Read, Read/Write, Signed/Unsigned, Decimal Places, Multiplier, Divisor, No of Bits, StartBit
OTA RemoteUpdate Software
Data-Exchange Values On Change
Alarms On Change
Events On Change
Measurements Default 900
Signal strength Is sent every 20 Min as a measurement
Offline Buffering Alarms, Events, Measurments ≈ 72h
SMS For Troubleshooting you can operate the device by SMS:

Reboot

Change tenant

FOTA/OTA

General

Dimensions 100 x 70 x 45 mm
Weight 89g
GSM Antenna SMA Connector
Power Supply Nominal voltage range: 12-24 VDC, 10%

Maximum continuous (average) supply power: 2.5 W

Maximum continuous (average) supply current: 200 mA at 12V, 100 mA at 24V

Mounting Via DIN Rail Adapter or Adapter for Wall Mounting
SIM Card Format 2FF
Operating temperature -20..60°C
Storage temperature -40..85°C
Oper. humidity Max. 85%
Storage humidity Max. 85%
IP Class IP20/IP54 (opt.)
Approvals
Conformity Declerations 2014/53/EU (Radio Equipment Directive – RED)

Radio

EN301511 v12.5.1 for GSM 900 and 1800 MHz

EN301908 v11.1.1 for UMTS band 1 and 8

EN300328 v2.1.1 for Bluetooth Low EnergyRoHS-DIrective 2011/65/EU

EMC

EN 301489-1 v2.1.1 general part

EN 301489-52 v0.0.7 for GSM and UMTS

EN 301489-17 v3.1.1 for for Bluetooth Low Energy

Safety

EN60950-01